No products in the cart.
Bluetooth, Wi-Fi, Wireless Communication
ESP32 OLED WiFi Modules+ Bluetooth Dual ESP-32
Availability:
Available on backorder
Features:
high performance – price – ratio
small volume, easy embedded to other products
strong function, with the support of lwip protocol, freertos
support three modes: ap, sta and ap + sta
support for lua program, easy to develop
৳ 990.00
Available on backorder
Introduction:
ESP32 with integrated antenna , power amplifier, low noise amplifiers, filters, and the power management module. The entire solution is the least amount of pcb area. This board has 2.4ghz dual mode wifi and Bluetooth chips by tsmc 40nm low power technology, power and rf characteristics of best, which is safe, reliable, and scalable to a wide range of applications.
Features:
high performance – price – ratio
small volume, easy embedded to other products
strong function, with the support of lwip protocol, freertos
support three modes: ap, sta and ap + sta
support for lua program, easy to develop
Based on 0 reviews
Be the first to review “ESP32 OLED WiFi Modules+ Bluetooth Dual ESP-32”
No more offers for this product!
General Inquiries
There are no inquiries yet.
Related products
- Arduino, Bluetooth, Boards, Wi-Fi
ESP32 rev1 Development Board WiFi+Bluetooth Ultra-Low Power Consumption Dual Cor
Arduino, Bluetooth, Boards, Wi-FiESP32 rev1 Development Board WiFi+Bluetooth Ultra-Low Power Consumption Dual Cor
Features of the ESP32 include the following:
For Course : https://github.com/Nabilphysics/ESP32_IoT_long_course_crux/wiki
Processors:
CPU: Xtensa dual-core (or single-core) 32-bit LX6 microprocessor, operating at 160 or 240 MHz and performing at up to 600 DMIPS
Ultra low power (ULP) co-processor
Memory: 520 KiB SRAM
Wireless connectivity:
Wi-Fi: 802.11 b/g/n
Bluetooth: v4.2 BR/EDR and BLE
Peripheral interfaces:
12-bit SAR ADC up to 18 channels
2 × 8-bit DACs
10 × touch sensors (capacitive sensing GPIOs)
4 × SPI
2 × I²S interfaces
2 × I²C interfaces
3 × UART
SD/SDIO/CE-ATA/MMC/eMMC host controller
SDIO/SPI slave controller
Ethernet MAC interface with dedicated DMA and IEEE 1588 Precision Time Protocol support
CAN bus 2.0
Infrared remote controller (TX/RX, up to 8 channels)
Motor PWM
LED PWM (up to 16 channels)
Hall effect sensor
Ultra low power analog pre-amplifier
Security:
IEEE 802.11 standard security features all supported, including WFA, WPA/WPA2 and WAPI
Secure boot
Flash encryption
1024-bit OTP, up to 768-bit for customers
Cryptographic hardware acceleration: AES, SHA-2, RSA, elliptic curve cryptography (ECC), random number generator (RNG)
Power management:
Internal low-dropout regulator
Individual power domain for RTC
5uA deep sleep current
Wake up from GPIO interrupt, timer, ADC measurements, capacitive touch sensor interruptSKU: n/a - Signal Switches, Touch, Wi-Fi
SONOFF® T1 UK 1-3 Gang AC 90V-250V 600W WIFI And RF 86 Type Smart Wall Touch Lig
Signal Switches, Touch, Wi-FiSONOFF® T1 UK 1-3 Gang AC 90V-250V 600W WIFI And RF 86 Type Smart Wall Touch Lig
Power Supply: 90V-250V AC
Max. Current: 2A/250V/gang
Max. Power: 600W/gang
Wireless Standard: WiFi 2.4GHz & 433MHz RF
Material: ABS V0+ Toughened Glass Panel
Dimension: 86mm*86mm
Weight: 130.0gPackage included:
1 x 86 Type UK Smart Wall Touch Light Switch Module
SKU: n/a - Shields, Wi-Fi
Node MCU Development Kit NodeMCU + Motor Shield WiFi ESP8266
IoT Course : https://github.com/Nabilphysics/ESP32_IoT_long_course_crux/wiki
All-function pins: SPI, UART, GPIO, AI and 3.3V power connector;
expand two-way motor-driven, two-way direct drive motor;
onboard power switch;
Motor power range: 4.5V ~ 36V;
Control power range: 4.5V ~ 9V;
Motor power, control power separation; In the experiment, by short-circuiting block the merger, the VIN and VM short, while power supply to the motor and the control board.SKU: n/a
There are no reviews yet.